Pinewood Derby Axle Guide Tool
thingiverse
I do not do it for money just to cover costs and helping out the Pinewood COmmunity Instructions 1) Place the axle guide into the slot that is pre-cut for the nail. 2) You should feel a small lip on each side of the car when the guide is installed...
Pinewood Derby Axle Guide Tool (remixed)
thingiverse
original instructions: 1) Place the axle guide into the slot that is pre-cut for the nail. 2) You should feel a small lip on each side of the car when the guide is installed properly. 3) Place the car and axle guide into a clamping device to hold...
Pinewood Derby axle drilling guide
thingiverse
This is a guide/jig for drilling axle holes on a Pinewood Derby car. One side is at 2.5mm above the bottom and the other at 3.5mm so you can run 3 wheels touching if your rules allow. If not, just use the same side for all 4 holes. It's sized for...
Pinewood Derby Axle Drilling Guide
thingiverse
This is a tool I made to help me line up my drill press for putting new axle holes in a Pinewood Derby car block. If your pack allows long wheel base cars, this can spot the holes for you. The centers of the holes are 1/8" up from the bottom of the...
Pinewood Derby Axle Tool
thingiverse
This tool helps one install wheels and axles on Pinewood Derby cars that use the saw slots in the blocks. Just hold or clamp it to the bottom with the ridge inside the slot, then gently push the wheels and axles in. Drilling a pilot hole for the...
Pinewood Derby Axle Mount
thingiverse
This fits snugly in the axle slot of a standard pinewood derby block and can be easily aligned and glued in place. The standard issue nail/axle fits in the hole with about 5 mm of the nail hanging out the back. If fits in snugly and in the ones...
Pinewood Derby Axle Bender
thingiverse
This is a printable variant of the Derby Worx Axle Bender tool for bending pinewood derby axles (nails). It prints in 3 parts and is assembled using #4 bolts - 1 to hold the two main pieces together, and another 2 to hold the clamp piece down for...
PInewood derby axle guards
thingiverse
Super simple but convenient to keep your axles straight before the race. Quick to print. Use up to six M3 or M2 self tapping screws to secure to the underside of the car. #4 wood screws from the big box stores also work, but they're a little big.
Pinewood Derby Axle Relief Jig
thingiverse
A simple guide to drill relief holes into a pinewood derby car using a 1/8" bit. This allows you to see the tips of the axle through the bottom of the car. ... The hole can be used to glue the axle in place as well as provide a way to remove the axle...
Pinewood Derby Wheel and Axle
thingiverse
Model of a Pinewood Derby Wheel and Axle, as close as I could get them to actual parts. Note, there is no lettering on the wheel. I have not printed a wheel yet so if you print one or a set of 4 please post the pics so I can see how they look. ...
Pinewood Derby Car Axle Keepers
thingiverse
These grab well, weight less and less chance of splitting the wood and didn't need pilot holes.) You will want to put the axle keeper on before inserting axles to help guide them down the slot. 1. Center the axle keeper on the slot. 2. Put in...
Pinewood Derby Axle Install Tool
thingiverse
Instructions 1) Place the axle guide into the slot that is pre-cut for the nail. 2) You should feel a small lip on each side of the car when the guide is installed properly. 3) Place the car and axle guide into a clamping device to hold both in...
Pinewood Derby Axle Drilling Template
thingiverse
This is a drilling template for pinewood derby car blocks. Drilling using a #44 bit is better than using the standard cut slots, which make alignment of the wheels difficult to make and maintain. With this template, you don't have to worry about...
Pinewood derby wheel gap guide
thingiverse
Put the guide between them, with the axel in the gap in the guide, and gently hammer your axel in until snug. Set to .4mm gap, which is relatively tight. ... Make sure you use a setting that is a multiple of your printer's layer height, so your slicer...
Pinewood Derby Axle Drilling Templates (Includes Remixes)
thingiverse
FYI, this is designed for a #44 drill bit (0.086") which is a commonly recommended size for drilling derby axle holes. These are not available at the big box stores. I picked mine up at Ace Hardware for a couple of bucks. You could also get away...
Pinewood Derby Axle / Wheel Push (Installer) Tool
thingiverse
A tool to help you push the axle into the body. I attempted to make is small enough that a Lion/Tiger could use it. The goal was to have 1 end with a preset gap to all a person to just push the axel in and the nail would already be gapped. I'm...
Pinewood Derby Car
thingiverse
Pinewood Derby Car body
ROPE PINEWOOD DERBY CAR
grabcad
SQUARE KNOT PINEWOOD DERBY CAR
Blazer Pinewood Derby template
thingiverse
Just a basic Pinewood Derby car template
Pinewood Derby - Sports Car
thingiverse
Design for a pinewood derby car.
Pinewood Derby Batmobile
thingiverse
Batmobile I designed for pinewood derby.
Pinewood Derby Model
grabcad
Intricate Pinewood derby car model. ...Untested in real life.
Superman Pinewood Derby Car
thingiverse
A sample Pinewood Derby car using the Superman logo.
Pinewood Derby Tri-Wing
thingiverse
This is a Tri-Wing tail for a Pinewood derby car inspired by an F22 tail. ...Fits and unmodified pinewood derby car width.
Co2 Pinewood Derby Car
thingiverse
Just a little thing I made for my no rules Pinewood Derby. ...Takes 12g co2 cartridges.
Pinewood Derby Car
thingiverse
A Pinewood Derby Car with the standard wheelbase for Cub Scouts
Pinewood Derby Car
sketchfab
This is just a simple model of a Pinewood Derby Car.
Pinewood Derby Track Cleaner
thingiverse
Used along with pledge wipes to clean the racing surface of a BestTrack pinewood derby track.
Pinewood Derby Spoiler
thingiverse
This is a spoiler that may be glued to a pinewood derby, or similarly sized, car.
Pinewood Derby Car
grabcad
The pinewood derby race car design was influenced by Doctor Jobe's work (pinewoodderbyphysics.com). The rear section comprises solid lead, while the front utilizes the pinewood block. Large gauge hypodermic needle tubing forms the side rails. Both...
